| Pulse Functions |
| Single | One pulse at each selected period up to 50MHz repetition rate |
| Double | One pair of pulses at each period up to 25MHz repetition rate. Both pulses have the same selected width; the position of the second pulse set by the delay control. |
| Operating Modes |
| Continuous | Output continuous at programmed period rate. |
| Triggered | Output quiescent until triggered by an internal, external, GPIB or manual trigger, then generates one cycle at programmed period rate. |
| Gated | Same as triggered mode except pulses are output for the duration of the gated signal. The last cycle started is completed |
| Burst | Same as triggered mode for programmed number of cycles from 2 to 999,999 as set by the N-BURST function |
| External Width | Trigger duration and rate sets pulse width and repetition |
| Timing Characteristics |
| Period |
| Range | 20.0 ns to 10s (50MHz to 0.1Hz repetition rate) |
| Resolution | Up to 6 digits limited to 0.1 ns |
| Accuracy | ±1% of setting ±1 ns. |
| Jitter | < 0.1 % of setting +50 ps, decreasing to 0.01 % on slowest range |
| Width |
| Range | 10 ns to 9.89999 s limited by 8 ns off time |
| Resolution | Up to 6 digits limited to 0.1 ns |
| Accuracy | ±2% of setting ±2 ns |
| Jitter | <(0.1% of setting + 50 pS) decreasing to 0.005% on
slowest range |
| Delay |
| Range | 0 ns to 9.80000 s limited by the pulse width and 8 ns off time |
| Resolution | Up to 6 digits limited to 0.1 ns |
| Accuracy | ±2% of setting ±2 ns |
| Jitter | < 0.1% of setting +50 ps, decreasing to 0.005% on slowest range |
| Duty Cycle |
| Range | 1 to 99% |
| Resolution | 3 digits (0.1%) |
| Accuracy | Limited by width and pulse accuracy |
| Output Characteristics |
| Amplitude |
| High Level Range | -7.90V to+8.00V into 50 Ω (-15.8V to +16V in open circuit) |
| Low Level Range | -8.00V to +7.90V into 50 Ω (-16V to +15.8V in open circuit) |
| Amplitude Range | 0.1V to 16V p-p into 50 Ω load (32V p-p max in open circuit) |
| Resolution | 3 digits limited to 10mV |
| Accuracy | ±1% of level setting ±2% of pk-pk amplitude 50 mV into 50 O load |
| Aberrations | <5% + 50mV into 50 Ω load, for pulse levels between ±5V |
| Output Resistance | 50 ohms |
| Transition Times |
| Range | <5 ns to 100 ms variable. Leading and trailing edges settable separately and limited to 20:1 ratio between settings into one of the following ranges: 5ns-100ns;50ns-1.0us;500ns-10us; 5.0us-100us; 50us-1.0ms; 500us-10ms; 5ms-100ms |
| Resoultion | 3 digits limited to 0.1 ns |
| Accuracy | ±5% of setting ±2 ns |
| Linearity | <5% deviation from a straight line between 10% and 90% points |
| Internal trigger |
| Range | 100 nS to 99.99 s |
| Resolution | 4 digits limited to 100 ns |
| Accuracy | 0.01% ±1ns |
| Jitter | <0.1 % of setting +50 ps |
| Inputs And Outputs Trigger Input |
| Sensitivity | 500Vp-p minimum |
| Minimum Width | 10ns |
| Maximum Rate | 50 MHz |
| Input Impedance | 1 M Ω |
| Input Protection | ±20V DC plus peak AC |
| Range | Selectable from -10V to +10V |
| Resolution | 3 digits limited to 10mV |
| Accuracy | ±5% of setting ±50 mV |
| Slope Selection | Positive or Negative |
| Sync Output |
| A TTL level pulse at programmed period. Output impedance is 50 Ω, protected against short circuit. The high level is >2.4V into 50 Ω. |
| GPIB Programming |
| Specification | IEEE-488.2 |
| Compatibility | With HP8112A GPIB command set.. |
| Address | 0-30 front panel selected |
| General |
| Memory | Non-volatile stores up to 99 complete panel settings.
Last user setup also retained at power down. |
| Power Requirements | 90-256V, 48-66 Hz, 70VA maximum |
Dimensions
(Without Rack Mount Kit) | 8.9 cm (3.5 in) H x 21.3 cm (8.4 in)W x 35.7 cm(14 in) L |
| Weight | 4 kg Net |
Operating
Temperature | 0° C to 50° C |
| Storage Temperature | 20°C - +60° |
| Humidity | 95% RH, 0°C to 30°C, 75% RH to 40°C, 45% RH to 50°C |
| Accessories | 19’ rack mount kit,optional |
| CE Compliant | Yes |
|